|
|
|
 | Three guns for paint, three guns for beads. |
| Quartz controlled time and distance delays for
accurate line lengths and perfect paint/bead alignment at any speed. |
| Four built-in footage counters. |
| Premark system for line premarking and job surveys. |
| Select English or Metric without recalibration, even
while painting. |
| Fast, easy electronic calibration with built in
pulse multiplication. |
| Precision speedometer is built-in. |
| Cycle-Track™ and Cycle-Lock™ ease retracing. |
| Automatic skip clock reset on skipline start. |
| Fast cycle change while painting. |
| Power off memory for all settings and accumulated
data. |
| Easy-to-use menus for all settings. |
| Illuminated display for nighttime use. |
| Short circuit protected outputs with warning message. |
| Open solenoid circuit warning on display. |
| Power Input: 11-18 Volts DC, negative
ground, 0.5 amperes plus solenoid draw. Fully protected against reverse
polarity and voltage spikes. |
| Solenoid Outputs: 3 outputs for paint
solenoids, 3 outputs for beads solenoids, each rated at 2 amperes, switching
to ground. 5 ampere fuse supplied. Total draw not to exceed 8 amperes (fuse
must be replaced for 8 ampere draw). |
| Sender Input: Inputs for zero-speed (NPN open
collector) or self-generating (near-zero-speed) senders. Power is
supplied (12v) for zero speed senders. |
| Maximum operating speed: 40 MPH (64 km/hr).
Speed is generally limited by valve speed, control hose length and paint
delivery rate. |
| Minimum operating speed: 0 MPH with zero-speed
senders, 0.1 MPH with near-zero-speed senders. When used with internal
pulse multiplication of X4 or greater, minimum speed is 1.7 MPH (2.7 km/hr). |
| Timers: Time delays for Paint On, Paint Off, Beads
On, and Beads Off (all 0 to 0.5 sec). One distance delay for the bead guns (0
to 5
ft (1.5m). These timers allow precise compensation of gun activation and
release delays for precise line lengths and perfect bead alignment. |
| Front Panel: Switches are heavy-duty military
standard sealed toggle switches. The display is a 16-character by two line
illuminated alpha-numeric LCD. Pushbuttons are long-life sealed membrane
switches. |
| Footage Range: Paint and cycle may be set in
increments of 0.1 ft. (0.03m) from 1 ft. (0.304m) to 999.9 ft. (304.8m). |
| Footage Counters: One for each paint line and one
odometer (total travel), with a maximum reading of 1,677,721.5 ft
(511,369.5m). One footage totalizer for paint line lengths. Counters are
individually resettable to zero. |
| Power-off Memory: Stores all settings and
accumulated data. This memory is automatically updated when power is turned
off, and requires no power or batteries for maintenance. |
| Temperature Range: 32ºF to 130ºF (0ºC to 55ºC).
The effect of temperature on accuracy is too small to measure. |
| Cable supplied: 15 feet (4.5m) in each of four
branches (Power, Sender, Centerline Solenoid, Edgeline Solenoid). Cables to
any length are available for nominal additional charge. |
| The CS33A cabinet is heavy cast aluminum, painted with a semi-flat textured epoxy enamel that is water and solvent resistant. The panel is non-glare polycarbonate, screened on the reverse side for long life. The CS33A is supplied with a steel mounting yoke with adjustable hand knobs for convenient mounting. |
|
Send mail to jb46(at)woh.rr.com
with
questions or comments about this web site.
|
